- Version
- 1.0.29
- Published
- Windows signature
- Not signed
Windows blocks files downloaded from the Internet by default — that is its own security mechanism, not a problem with the installer. This build carries no digital signature yet, so the first run asks you to confirm; the download page shows what to expect and how to get past it.
Added
- project_create_wall_foundation_safe creates a wall foundation under each named straight basic wall in one checkpoint, reads every footing back, and rolls the whole call back when a wall is refused or a readback does not match. type_set_wall_foundation_safe duplicates a wall foundation type, sets its usage, thickness, width, toe, heel, end extension, do-not-break and material values, and verifies each value by readback.
- spatial_clash_detect lists, for each candidate pair of solids, whether it was evaluated and why it was not. When some pairs were not evaluated, the answer says so instead of reporting a clean no-clash, and the clashes that were decided stay in the answer.
- type_list_element_types returns the wall kind (basic, curtain, stacked, or unknown) for wall types.
- rebar_create_column_cage_safe and rebar_create_beam_cage_safe report the number of warnings Revit raised while creating the bars and the start and end hook orientation chosen for each stirrup.
- A mutating tool result whose change record cannot be read now carries a warning diagnostic instead of silently dropping the record.
- Revit 2024 through 2027 are tested on disposable models in live Revit sessions covering column and beam cage creation with hooks (dry run, execute, and delete), the warning count and hook orientations on cage results, and the refusal of bars from different layers that sit too close together. The refusals for non-prismatic columns and sloped non-prismatic beams are not yet tested in a live Revit session. The wall foundation, stairs, curtain grid, clash, and family changes in this release were not part of its live Revit test. Revit 2021, 2022, and 2023 are included in the installer and are not yet tested in a live Revit session.
Changed
- The dry run of rebar_create_column_cage_safe and rebar_create_beam_cage_safe creates the same hooked bars as execute, checks them against the host solid at the same tolerance, and rolls back, so a bar that would fall outside the host is reported in the dry run.
- A longitudinal bar with no hook at an end no longer needs a hook orientation at that end.
- Wall foundation usage (bearing or retaining) is read and written with the encoding measured on Revit 2024 through 2027. The toe side of a flipped wall is not measured yet.
- project_create_stair_safe checks the stairs type riser and tread rules before it opens the edit scope, reads back the run, landing and riser counts inside the scope, and cancels the scope when they differ from the plan.
- curtain_grid_create_safe resolves the curtain wall vertical extent first, and on any failure rolls back and clears its output instead of leaving a partial grid.
Fixed
- Hooked stirrups and bars in column and beam cages are no longer refused as outside the host: each hook side comes from the measured bar direction at both ends.
- A column or beam cage whose layers place bars closer than the larger bar diameter or the minimum clear spacing is refused, instead of being reported verified while Revit warned of identical bars.
- Family authoring refuses a catalog whose units do not match the family, a blend whose sections do not match, a void cut that does not reduce the volume, and a sketch tie that remains, and rolls the checkpoint back.
- Family profile edits resolve the sketch for each form, refuse sweep profile symbols and blend profile edits with a named error, create the blend from the top and bottom profiles in the order Revit expects, and check that a material parameter can be associated before associating it.
- spatial_solid_read and spatial_section_slice on a combined family form read the owning combination. In a family document, geometry_join_apply combines the elements through Revit and reads the combination members back, refuses cut-order and switch-order joins, void and non-combinable elements, and pairs that are already combined. geometry_unjoin is refused in a family document, and geometry_join_plan reads the combination membership.